How to refill Samsung MLT-D105L MLTD105L ML-1915, ML-2525, ML-2525W, ML-2580n, SCX-4600, SCX-4623F, SCX-4623FW, SF-650, SF-650P
Author: Tin Nguyen Views: 17387 Created: 2012-07-20 22:45 Last Updated: 2012-07-27 16:59 100 Rating/ 2 Voters

How to refill Samsung MLT-D105L MLTD105L ML-1915, ML-2525, ML-2525W, ML-2580n, SCX-4600, SCX-4623F, SCX-4623FW, SF-650, SF-650P

DELL 1130 1130n 1133 1135n 

Take the cartridges out of printer, using the paper town to cover the drum (green parts) of the cartridges. This will help to protect the drum to explode to the light.

 

Place the cartridge in horizontal position with the side cover holding the chips facing you. Take the blade and cut the head of the plastic rivet. Be careful with the movement, keeping the blade from slipping and cutting yourself, there 4 of these on the cartridge.

 

After cut all 4 plastic rival, using the small screwdriver, slightly separate the cover.

 

 

Using the small plier, or a knife to cut (break) a section on the plastics cover.so we insert the small flat head screwdriver to remove the plug easy later. This is the optional step you do not need to do it.

 

 

Remove the fill plug and Empty the hopper/cartridge and clean thoroughly by using a vacuum.. This step is very important; better cleaning of the cartridge and not mixing previous toner with new toner, the better quality printing result.

 

 

After cleaning the cartridges Fill the toner hopper with the proper amount of toner for use in Samsung D105 cartridges, and tightly close with the plastic

 

 

Install the end cap and use any tape to secure it together. Make sure that the tapes are not covering the chip or any metal contact.

 

 

Replace the chip with a new one and sliding it in place.

NOTE: Under normal working conditions the printer will eventually call for toner cartridge replacement. The printer will need to read a new chip to reset the counters and to print. For this reason, it is recommended that testing be done with a shop chip first and once print quality is assured, a new chip be installed in its place.

 

Rss Comments 5
  • #
    [ Dumanmk]: chip 2013-12-18 02:36

    I bought toner powder for ML 2525 and I put it .But I didnt understand about chip.What I have to make .I can not see on smart panel for toner level full. What I have to make ?

  • #
    [ Dumanmk]: chip 2013-12-18 02:31

    I bought toner powder for ML 2525 and I put it .But I didnt understand about chip.What I have to make .I can not see on smart panel for toner level full. What I have to make ?

  • #
    [ hokester]: Toner Refilled. 2013-03-22 18:55

    I left a comment earlier today about the screws, then I got some inspiration from the Lord to use a sharp pointed soldering iron an just melt it a little so that it mushrooms out a little and it is secured. better that screws or tape.

  • #
    [ hokester]: Toner refilled, BUT. 2013-03-22 17:56

    You give us instructions to cut the plastic rivets, but you did not include the 5 screws to close it up again. Maybe you will for the next ones you mail out.

  • #
    [ Tigerbalm]: instructions 2013-03-18 02:13

    I did not have to break any plastic around plug. Just use small screwdriver and pry the plug up. The refill worked great on my original cartridge, but there was more toner than needed. So be careful when adding toner. Do it slowly and watch the level! It only took me about 15 minutes to refill and now my printer prints great! Thanks. I will NEVER by a new cartridge or re-manuf. one again!

Info Add Comment
Nickname: Your Email: Subject: Comment:
Enter the code below:
Quick Jump Menu